Sittings · Document

Report (COM(2023)0451 – C9-0308/2023 – 2023/0284(COD)) 2025-09-03

Circularity requirements for vehicle design and management of end-of-life vehicles

3.9.2025 A10-0158/395

Amendment 395

Silvia Sardone, Filip Turek, Nikola Bartůšek, Elisabeth Dieringer, Roman Haider, Anne-Sophie Frigout, Mathilde Androuët, Ondřej Knotek, Jana Nagyová

on behalf of the PfE Group

Report A10-0158/2025

Jens Gieseke

Circularity requirements for vehicle design and management of end-of-life vehicles

(COM(2023)0451 – C9-0308/2023 – 2023/0284(COD))

Proposal for a regulation

Recital 19

Text proposed by the Commission

Amendment

(19) In view of the low recycling rate for plastics, especially from end-of-life vehicles, and the overall negative impacts of other forms of treatment of plastic waste, it is appropriate to increase the uptake of recycled plastics in vehicles. To this end, a mandatory target for plastic recycled from post-consumer waste should be included in new vehicles. Accordingly, each vehicle type should contain twenty-five percent of plastic recycled from post-consumer plastic waste. Twenty-five percent of this recycled content target for plastics should be achieved by including plastics recycled from end-of-life vehicles in the vehicle type concerned. In order to ensure uniform conditions for the implementation this obligation, implementing powers should be conferred on the Commission to establish methodology for the calculation and verification of the share of plastics recovered from post-consumer waste, and from end-of-life vehicles respectively, present in and incorporated into the vehicle type.

(19) In view of the low recycling rate for plastics, especially from end-of-life vehicles, and the overall negative impacts of other forms of treatment of plastic waste, it is appropriate to increase the uptake of recycled plastics in vehicles. To this end, a mandatory target for plastic recycled from post-consumer waste should be included in new vehicles. Accordingly, each vehicle type should contain ten percent of plastic recycled from pre-consumer plastic waste and post-consumer plastic waste. In order to ensure uniform conditions for the implementation this obligation, implementing powers should be conferred on the Commission to establish methodology for the calculation and verification of the share of plastics recovered from post-consumer waste, and from end-of-life vehicles respectively, present in and incorporated into the vehicle type.

Or. en

3.9.2025 A10-0158/396

Amendment 396

Filip Turek, Silvia Sardone, Mathilde Androuët, Nikola Bartůšek, Elisabeth Dieringer, Roman Haider, Anne-Sophie Frigout, Ondřej Knotek, Jana Nagyová

on behalf of the PfE Group

Report A10-0158/2025

Jens Gieseke

Circularity requirements for vehicle design and management of end-of-life vehicles

(COM(2023)0451 – C9-0308/2023 – 2023/0284(COD))

Proposal for a regulation

Article 2 – paragraph 6 – introductory part

Text proposed by the Commission

Amendment

6. Notwithstanding paragraph 1, points (b) and (c), Articles 16, 19, 20, 27 and 46 to 49 shall apply to vehicles and end-of-life vehicles of categories L3, L4, L5, L6 L7, M2, M3, N2, N3 and O with the following modifications:

6. Without prejudice to paragraph 1, points (b) and (c), Articles 16, 19, 20, 27 and 46 to 49 shall apply to vehicles and end-of-life vehicles of categories L, M2, M3, N2, N3 and O and to parts other than the base vehicle of a vehicle of category N1, N2, N3, M2 or M3 which has not been approved in a single-stage type approval, with the following modifications:

Or. en

3.9.2025 A10-0158/397

Amendment 397

Silvia Sardone, Filip Turek, Mathilde Androuët, Nikola Bartůšek, Elisabeth Dieringer, Roman Haider, Anne-Sophie Frigout, Ondřej Knotek, Jana Nagyová

on behalf of the PfE Group

Report A10-0158/2025

Jens Gieseke

Circularity requirements for vehicle design and management of end-of-life vehicles

(COM(2023)0451 – C9-0308/2023 – 2023/0284(COD))

Proposal for a regulation

Article 3 – paragraph 1 – point 9

Text proposed by the Commission

Amendment

(9) ‘plastic’ means a polymer within the meaning of Article 3, point (5), of Regulation (EC) No 1907/2006, to which additives or other substances may have been added;

(9) ‘plastic’ means a polymer within the meaning of Article 3, points (2) and (3), of Regulation (EU) No 10/2011, to which additives or other substances may have been added, capable of functioning as a main structural component of final materials and articles, including biobased plastic, and excluding adhesives, coatings and sealants.

Or. en

3.9.2025 A10-0158/398

Amendment 398

Silvia Sardone, Filip Turek, Mathilde Androuët, Nikola Bartůšek, Elisabeth Dieringer, Roman Haider, Anne-Sophie Frigout, Ondřej Knotek, Jana Nagyová

on behalf of the PfE Group

Report A10-0158/2025

Jens Gieseke

Circularity requirements for vehicle design and management of end-of-life vehicles

(COM(2023)0451 – C9-0308/2023 – 2023/0284(COD))

Proposal for a regulation

Article 3 – paragraph 1 – point 9 a (new)

Text proposed by the Commission

Amendment

(9 a) ‘biobased plastics’ means plastics made from biological resources, such as biomass, feedstock, organic waste or by-products, and irrespective of whether the plastics are biodegradable or not;

Or. en

3.9.2025 A10-0158/399

Amendment 399

Silvia Sardone, Filip Turek, Mathilde Androuët, Nikola Bartůšek, Elisabeth Dieringer, Roman Haider, Anne-Sophie Frigout, Ondřej Knotek, Jana Nagyová

on behalf of the PfE Group

Report A10-0158/2025

Jens Gieseke

Circularity requirements for vehicle design and management of end-of-life vehicles

(COM(2023)0451 – C9-0308/2023 – 2023/0284(COD))

Proposal for a regulation

Article 3 – paragraph 1 – point 15

Text proposed by the Commission

Amendment

(15) ‘authorised treatment facility’ means any establishment or undertaking that is permitted in accordance with Directive 2008/98/EC and this Regulation to carry out collection and treatment of end-of-life vehicles;

(15) ‘authorised treatment facility’ means any establishment or undertaking that is permitted in accordance with Directive 2008/98/EC and this Regulation to carry out the collection and storage of end-of-life vehicles or of their parts and components, the issuance of the certificate of destruction, the depollution of end-of-life vehicles, and the removal of parts and components and parts, where technically feasible and economically sustainable;

Or. en

3.9.2025 A10-0158/400

Amendment 400

Filip Turek, Silvia Sardone, Mathilde Androuët, Nikola Bartůšek, Elisabeth Dieringer, Roman Haider, Anne-Sophie Frigout, Ondřej Knotek, Jana Nagyová

on behalf of the PfE Group

Report A10-0158/2025

Jens Gieseke

Circularity requirements for vehicle design and management of end-of-life vehicles

(COM(2023)0451 – C9-0308/2023 – 2023/0284(COD))

Proposal for a regulation

Article 3 – paragraph 1 – point 22

Text proposed by the Commission

Amendment

(22) ‘producer’ means any manufacturer, importer or distributor who, irrespective of the selling technique used, including by means of distance contracts as defined in Article 2, point (7), of Directive 2011/83/EU, supplies a vehicle for the first time for distribution or use, within a territory of a Member States on a professional basis;

Or. en

3.9.2025 A10-0158/401

Amendment 401

Silvia Sardone, Filip Turek, Mathilde Androuët, Nikola Bartůšek, Elisabeth Dieringer, Roman Haider, Anne-Sophie Frigout, Ondřej Knotek, Jana Nagyová

on behalf of the PfE Group

Report A10-0158/2025

Jens Gieseke

Circularity requirements for vehicle design and management of end-of-life vehicles

(COM(2023)0451 – C9-0308/2023 – 2023/0284(COD))

Proposal for a regulation

Article 6

Text proposed by the Commission

Amendment

[...]

deleted

Or. en

3.9.2025 A10-0158/402

Amendment 402

Silvia Sardone, Filip Turek, Mathilde Androuët, Nikola Bartůšek, Elisabeth Dieringer, Roman Haider, Anne-Sophie Frigout, Ondřej Knotek, Jana Nagyová

on behalf of the PfE Group

Report A10-0158/2025

Jens Gieseke

Circularity requirements for vehicle design and management of end-of-life vehicles

(COM(2023)0451 – C9-0308/2023 – 2023/0284(COD))

Proposal for a regulation

Article 6 – paragraph 1 – subparagraph 1

Text proposed by the Commission

Amendment

The plastic contained in each vehicle type that is type-approved as of [OP: Please insert the date = the first day of the month following 72 months after the date of entry into force of the Regulation] under Regulation (EU) 2018/858 shall contain a minimum of 25 % of plastic recycled by weight from post-consumer plastic waste.

The plastic contained in each new vehicle type that is type-approved as of [OP: Please insert the date = the first day of the month following 72 months after the date of entry into force of the Regulation] under Regulation (EU) 2018/858 shall contain a minimum of 10 % of plastic recycled by weight from pre-consumer plastic waste and post-consumer plastic waste.

Or. en